A2/304 grade stainless steel stitching moulded fasteners, supplied pre-assembled with an aluminium / EPDM rubber 19mm diameter sealing washer.
Standard stock colours are available for next-day delivery, special colours have an extended lead time which will be confirmed on your order acknowledgement - please call us if you wish to confirm a lead time before ordering.
Estimated lead times
1-4 Days
Estimated lead times
1-4 Days
Stainless steel nylon moulded head fasteners for steel sheet stitching.
Order information: We can supply or match almost any RAL, BS or NCS colour, please call 0800 304 7616 if the colour you require is not available on the colour drop down. For some sizes or colours there may be a longer lead time, please call 0800 304 7616 if you wish to confirm before placing the order.
- Precisely matched colour head
- Genuine A2 stainless steel for optimum corrosion resistance
- Free spin zone assists installers to ensure fasteners are not over-driven
- Supplied pre-assembled with an Aluminium / EPDM rubber 19mm diameter sealing washer, normally used in roof applications
- For mechanically fixing (stitching) two metal sheets up to 1mm thick together
|
Years / Environment
|
||||||
|---|---|---|---|---|---|---|
| Interior | Rural | Urban | Industrial / Coastal | Marine | Swimming pools & Chemical plants | |
| Corrosivity Category | C1 | C2 | C3 | C4 | C5 | - |
| Austenitic Stainless Steel A2 Grade (304) | 30 | 25 | 25 | 15 | 0 | 0 |
|
Substrate
Steel
|
0.5 mm |
| Steel | |
| 0.5 mm | 1.25 kN |
| NR,II,K (Tensile - Pull-out) | 0.5mm Steel: 0.6 kN |
|
Substrate
Steel
|
A19 Washer |
| Steel | 0.5 mm |
| 0.5 mm | 3.38 kN |
| Installation tool | Variable speed electric screw gun |
| Installation drive | Fixfast Matchfast BlueDrive |
| Installation speed | 1500 RPM |
| Correct installation | Fasteners should be driven within three degrees of perpendicular to the surface of the fastened material. Use a depth-setting nosepiece to avoid over-driving, and do not over-tighten. Variants with bonded washers should not have the rubber compressed to less than two-thirds of its uncompressed height. Care should be taken when engaging and disengaging from the fastener head to avoid damage to the protective coating. |
| Handling | Fasteners may have sharp edges, and the use of power tools can be dangerous. Use personal protective equipment. Store fasteners in dry conditions. Inspect each fastener before use and do not use damaged fasteners. |
Stainless steel nylon moulded head fasteners for steel sheet stitching.
Order information: We can supply or match almost any RAL, BS or NCS colour, please call 0800 304 7616 if the colour you require is not available on the colour drop down. For some sizes or colours there may be a longer lead time, please call 0800 304 7616 if you wish to confirm before placing the order.
- Precisely matched colour head
- Genuine A2 stainless steel for optimum corrosion resistance
- Free spin zone assists installers to ensure fasteners are not over-driven
- Supplied pre-assembled with an Aluminium / EPDM rubber 19mm diameter sealing washer, normally used in roof applications
- For mechanically fixing (stitching) two metal sheets up to 1mm thick together
|
Years / Environment
|
||||||
|---|---|---|---|---|---|---|
| Interior | Rural | Urban | Industrial / Coastal | Marine | Swimming pools & Chemical plants | |
| Corrosivity Category | C1 | C2 | C3 | C4 | C5 | - |
| Austenitic Stainless Steel A2 Grade (304) | 30 | 25 | 25 | 15 | 0 | 0 |
|
Substrate
Steel
|
0.5 mm |
| Steel | |
| 0.5 mm | 1.25 kN |
| NR,II,K (Tensile - Pull-out) | 0.5mm Steel: 0.6 kN |
|
Substrate
Steel
|
A19 Washer |
| Steel | 0.5 mm |
| 0.5 mm | 3.38 kN |
| Installation tool | Variable speed electric screw gun |
| Installation drive | Fixfast Matchfast BlueDrive |
| Installation speed | 1500 RPM |
| Correct installation | Fasteners should be driven within three degrees of perpendicular to the surface of the fastened material. Use a depth-setting nosepiece to avoid over-driving, and do not over-tighten. Variants with bonded washers should not have the rubber compressed to less than two-thirds of its uncompressed height. Care should be taken when engaging and disengaging from the fastener head to avoid damage to the protective coating. |
| Handling | Fasteners may have sharp edges, and the use of power tools can be dangerous. Use personal protective equipment. Store fasteners in dry conditions. Inspect each fastener before use and do not use damaged fasteners. |
