Carbon steel fastener for fixing timber batten to composite panel / liner tray.
Estimated lead times
1 Day
Estimated lead times
1 Day
Estimated lead times
1 Day
Estimated lead times
1 Day
Carbon steel countersunk fasteners for fixing timber battens to composite panels in tile support systems and in structural tray systems.
Features
- DF-TB accepted for use with Tactray 90 systems
- Superior quality carbon steel
- Excellent drilling and tapping performance
- Unique Enduroguard coating for excellent corrosion resistance
- For mechanically fixing timber battens and timber-like materials to thin steel
Years / Environment
|
|||||||
---|---|---|---|---|---|---|---|
Interior | Semi-interior | Rural | Urban | Industrial / Coastal | Marine | Swimming pools & Chemical plants | |
Corrosivity Category | C1 | - | C2 | C3 | C4 | C5 | - |
Carbon steel case hardened | 25 | 20 | 12 | 0 | 0 | 0 | 0 |
Years / Environment
|
|||||||
---|---|---|---|---|---|---|---|
Interior | Semi-interior | Rural | Urban | Industrial / Coastal | Marine | Swimming pools & Chemical plants | |
Corrosivity Category | C1 | - | C2 | C3 | C4 | C5 | - |
Carbon steel case hardened | 25 | 20 | 12 | 0 | 0 | 0 | 0 |
Years / Environment
|
|||||||
---|---|---|---|---|---|---|---|
Interior | Semi-interior | Rural | Urban | Industrial / Coastal | Marine | Swimming pools & Chemical plants | |
Corrosivity Category | C1 | - | C2 | C3 | C4 | C5 | - |
Carbon steel case hardened | 25 | 20 | 12 | 0 | 0 | 0 | 0 |
NR,II,K (Tensile - Pull-out) | 0.7mm Steel: 0.86 kN |
1.2mm Steel: 1.97 kN |
NR,II,K (Tensile - Pull-out) | 0.7mm Steel: 0.86 kN |
1.2mm Steel: 1.97 kN |
NR,II,K (Tensile - Pull-out) | 0.7mm Steel: 0.86 kN |
1.2mm Steel: 1.97 kN |
Installation tool | Variable speed electric screw gun |
Installation drive | TX30 |
Installation speed | 1500 RPM |
Correct installation | Fasteners should be driven within three degrees of perpendicular to the surface of the fastened material. Use a depth-setting nosepiece to avoid over-driving, and do not over-tighten. Variants with bonded washers should not have the rubber compressed to less than two-thirds of its uncompressed height. Care should be taken when engaging and disengaging from the fastener head to avoid damage to the protective coating. |
Handling | Fasteners may have sharp edges, and the use of power tools can be dangerous. Use personal protective equipment. Store fasteners in dry conditions. Inspect each fastener before use and do not use damaged fasteners. |
Carbon steel countersunk fasteners for fixing timber battens to composite panels in tile support systems and in structural tray systems.
Features
- DF-TB accepted for use with Tactray 90 systems
- Superior quality carbon steel
- Excellent drilling and tapping performance
- Unique Enduroguard coating for excellent corrosion resistance
- For mechanically fixing timber battens and timber-like materials to thin steel
Years / Environment
|
|||||||
---|---|---|---|---|---|---|---|
Interior | Semi-interior | Rural | Urban | Industrial / Coastal | Marine | Swimming pools & Chemical plants | |
Corrosivity Category | C1 | - | C2 | C3 | C4 | C5 | - |
Carbon steel case hardened | 25 | 20 | 12 | 0 | 0 | 0 | 0 |
Years / Environment
|
|||||||
---|---|---|---|---|---|---|---|
Interior | Semi-interior | Rural | Urban | Industrial / Coastal | Marine | Swimming pools & Chemical plants | |
Corrosivity Category | C1 | - | C2 | C3 | C4 | C5 | - |
Carbon steel case hardened | 25 | 20 | 12 | 0 | 0 | 0 | 0 |
Years / Environment
|
|||||||
---|---|---|---|---|---|---|---|
Interior | Semi-interior | Rural | Urban | Industrial / Coastal | Marine | Swimming pools & Chemical plants | |
Corrosivity Category | C1 | - | C2 | C3 | C4 | C5 | - |
Carbon steel case hardened | 25 | 20 | 12 | 0 | 0 | 0 | 0 |
NR,II,K (Tensile - Pull-out) | 0.7mm Steel: 0.86 kN |
1.2mm Steel: 1.97 kN |
NR,II,K (Tensile - Pull-out) | 0.7mm Steel: 0.86 kN |
1.2mm Steel: 1.97 kN |
NR,II,K (Tensile - Pull-out) | 0.7mm Steel: 0.86 kN |
1.2mm Steel: 1.97 kN |
Installation tool | Variable speed electric screw gun |
Installation drive | TX30 |
Installation speed | 1500 RPM |
Correct installation | Fasteners should be driven within three degrees of perpendicular to the surface of the fastened material. Use a depth-setting nosepiece to avoid over-driving, and do not over-tighten. Variants with bonded washers should not have the rubber compressed to less than two-thirds of its uncompressed height. Care should be taken when engaging and disengaging from the fastener head to avoid damage to the protective coating. |
Handling | Fasteners may have sharp edges, and the use of power tools can be dangerous. Use personal protective equipment. Store fasteners in dry conditions. Inspect each fastener before use and do not use damaged fasteners. |