Checkout using your account
This form is protected by reCAPTCHA - the Google Privacy Policy and Terms of Service apply.
Checkout as a new customer
Creating an account has many benefits:
A4/316 grade stainless steel hex head fastener for fixing up to 300mm composite panel to heavy section steel.
Supplied pre-assembled with a 19mm diameter sealing washer, normally used in roof applications.
Estimated lead times
1 Day
Estimated lead times
1 Day
Hex head stainless steel fastener for fixing composite panels up to 300mm thick.
Years / Environment
|
|||||||
---|---|---|---|---|---|---|---|
Interior | Semi-interior | Rural | Urban | Industrial / Coastal | Marine | Swimming pools & Chemical plants | |
Corrosivity Category | C1 | - | C2 | C3 | C4 | C5 | - |
Austenitic Stainless Steel A4 Grade (316) | 40 | 40 | 40 | 40 | 25 | 25 | 0 |
Substrate
Composite panel
|
8 mm |
Steel | |
0.5 mm | 0.89 kN |
NR,II,K (Tensile - Pull-out) | 4mm Steel: 7.11 kN |
6mm Steel: 10.42 kN | |
8mm Steel: 15.27 kN |
Substrate
Steel
|
S19 washer |
Composite panel | 4 mm |
0.5 mm | 2.61 kN |
Installation tool | Variable speed electric screw gun |
Installation drive | Fixfast GreenDrive (8mm hex integral socket with retaining clip) |
Installation speed | 1500 RPM |
Correct installation | Fasteners should be driven within three degrees of perpendicular to the surface of the fastened material. Use a depth-setting nosepiece to avoid over-driving, and do not over-tighten. Variants with bonded washers should not have the rubber compressed to less than two-thirds of its uncompressed height. Care should be taken when engaging and disengaging from the fastener head to avoid damage to the protective coating. |
Handling | Fasteners may have sharp edges, and the use of power tools can be dangerous. Use personal protective equipment. Store fasteners in dry conditions. Inspect each fastener before use and do not use damaged fasteners. |
Hex head stainless steel fastener for fixing composite panels up to 300mm thick.
Years / Environment
|
|||||||
---|---|---|---|---|---|---|---|
Interior | Semi-interior | Rural | Urban | Industrial / Coastal | Marine | Swimming pools & Chemical plants | |
Corrosivity Category | C1 | - | C2 | C3 | C4 | C5 | - |
Austenitic Stainless Steel A4 Grade (316) | 40 | 40 | 40 | 40 | 25 | 25 | 0 |
Substrate
Composite panel
|
8 mm |
Steel | |
0.5 mm | 0.89 kN |
NR,II,K (Tensile - Pull-out) | 4mm Steel: 7.11 kN |
6mm Steel: 10.42 kN | |
8mm Steel: 15.27 kN |
Substrate
Steel
|
S19 washer |
Composite panel | 4 mm |
0.5 mm | 2.61 kN |
Installation tool | Variable speed electric screw gun |
Installation drive | Fixfast GreenDrive (8mm hex integral socket with retaining clip) |
Installation speed | 1500 RPM |
Correct installation | Fasteners should be driven within three degrees of perpendicular to the surface of the fastened material. Use a depth-setting nosepiece to avoid over-driving, and do not over-tighten. Variants with bonded washers should not have the rubber compressed to less than two-thirds of its uncompressed height. Care should be taken when engaging and disengaging from the fastener head to avoid damage to the protective coating. |
Handling | Fasteners may have sharp edges, and the use of power tools can be dangerous. Use personal protective equipment. Store fasteners in dry conditions. Inspect each fastener before use and do not use damaged fasteners. |