A4/316 grade stainless steel lacquered low profile fastener for fixing to heavy section steel.
Supplied pre-assembled with a 29mm diameter sealing washer, normally used for fastening rooflights.
Estimated lead times
2-3 Days
Estimated lead times
2-3 Days
Low profile stainless steel fasteners for use in single skin sheeting, facade and rainscreens and flashing / trim detail applications.
Features
- A4/316 grade stainless steel for durability
- Low profile head to complement the best in modern construction techniques
- Specialist RedDrive installation tool for optimum performance
- Supplied pre-assembled with aluminium / EPDM sealing washer, normally used for rooflight applications
- For mechanically fixing steel sheeting systems to heavy steel purlins and sections
Years / Environment
|
|||||||
---|---|---|---|---|---|---|---|
Interior | Semi-interior | Rural | Urban | Industrial / Coastal | Marine | Swimming pools & Chemical plants | |
Corrosivity Category | C1 | - | C2 | C3 | C4 | C5 | - |
Austenitic Stainless Steel A4 Grade (316) | 40 | 40 | 40 | 40 | 30 | 25 | 0 |
Substrate
Steel
|
4 mm |
Steel | |
0.5 mm | 2.02 kN |
NR,II,K (Tensile - Pull-out) | 4mm Steel: 2.80 kN |
6mm Steel: 3.09 kN | |
8mm Steel: 6.89 kN |
Substrate
Steel
|
A29 Washer |
Steel | 4 mm |
0.5 mm | 3.81 kN |
Installation tool | Variable speed electric screwdriver |
Installation drive | Fixfast RedDrive |
Installation speed | 1500 RPM |
Correct installation | Fasteners should be driven within three degrees of perpendicular to the surface of the fastened material. Use a depth-setting nosepiece to avoid over-driving, and do not over-tighten. Variants with bonded washers should not have the rubber compressed to less than two-thirds of its uncompressed height. Care should be taken when engaging and disengaging from the fastener head to avoid damage to the protective coating. |
Handling | Fasteners may have sharp edges, and the use of power tools can be dangerous. Use personal protective equipment. Store fasteners in dry conditions. Inspect each fastener before use and do not use damaged fasteners. |
Low profile stainless steel fasteners for use in single skin sheeting, facade and rainscreens and flashing / trim detail applications.
Features
- A4/316 grade stainless steel for durability
- Low profile head to complement the best in modern construction techniques
- Specialist RedDrive installation tool for optimum performance
- Supplied pre-assembled with aluminium / EPDM sealing washer, normally used for rooflight applications
- For mechanically fixing steel sheeting systems to heavy steel purlins and sections
Years / Environment
|
|||||||
---|---|---|---|---|---|---|---|
Interior | Semi-interior | Rural | Urban | Industrial / Coastal | Marine | Swimming pools & Chemical plants | |
Corrosivity Category | C1 | - | C2 | C3 | C4 | C5 | - |
Austenitic Stainless Steel A4 Grade (316) | 40 | 40 | 40 | 40 | 30 | 25 | 0 |
Substrate
Steel
|
4 mm |
Steel | |
0.5 mm | 2.02 kN |
NR,II,K (Tensile - Pull-out) | 4mm Steel: 2.80 kN |
6mm Steel: 3.09 kN | |
8mm Steel: 6.89 kN |
Substrate
Steel
|
A29 Washer |
Steel | 4 mm |
0.5 mm | 3.81 kN |
Installation tool | Variable speed electric screwdriver |
Installation drive | Fixfast RedDrive |
Installation speed | 1500 RPM |
Correct installation | Fasteners should be driven within three degrees of perpendicular to the surface of the fastened material. Use a depth-setting nosepiece to avoid over-driving, and do not over-tighten. Variants with bonded washers should not have the rubber compressed to less than two-thirds of its uncompressed height. Care should be taken when engaging and disengaging from the fastener head to avoid damage to the protective coating. |
Handling | Fasteners may have sharp edges, and the use of power tools can be dangerous. Use personal protective equipment. Store fasteners in dry conditions. Inspect each fastener before use and do not use damaged fasteners. |