Checkout using your account
This form is protected by reCAPTCHA - the Google Privacy Policy and Terms of Service apply.
Checkout as a new customer
Creating an account has many benefits:
A4/316 grade stainless steel fastener for fixing halters to timber or light section steel up to 2.0mm, supplied pre-assembled with a stainless steel 19mm sealing washer.
Estimated lead times
1 Day
Estimated lead times
1 Day
Stainless steel fasteners for fixing clips and halters to light steel and timber purlins and rails
Features
Years / Environment
|
|||||||
---|---|---|---|---|---|---|---|
Interior | Semi-interior | Rural | Urban | Industrial / Coastal | Marine | Swimming pools & Chemical plants | |
Corrosivity Category | C1 | - | C2 | C3 | C4 | C5 | - |
Austenitic Stainless Steel A4 Grade (316) | 40 | 40 | 40 | 40 | 30 | 25 | 0 |
Substrate
Steel
|
1.2 mm |
Steel | |
0.5 mm | 1.61 kN |
NR,II,K (Tensile - Pull-out) | 0.5mm Steel: 0.91 kN |
1.2mm Steel: 2.97 kN | |
2mm Steel: 5.48 kN | |
18mm Plywood: 1.9 kN | |
Softwood C16: 2.19 kN |
Substrate
Steel
|
S19 washer |
Steel | 2 mm |
0.5 mm | 3.39 kN |
Installation tool | Variable speed electric screwdriver |
Installation drive | Fixfast GreenDrive (8mm hex integral socket with retaining clip) |
Installation speed | 1500 RPM |
Correct installation | Fasteners should be driven within three degrees of perpendicular to the surface of the fastened material. Use a depth-setting nosepiece to avoid over-driving, and do not over-tighten. Variants with bonded washers should not have the rubber compressed to less than two-thirds of its uncompressed height. Care should be taken when engaging and disengaging from the fastener head to avoid damage to the protective coating. |
Handling | Fasteners may have sharp edges, and the use of power tools can be dangerous. Use personal protective equipment. Store fasteners in dry conditions. Inspect each fastener before use and do not use damaged fasteners. |
Stainless steel fasteners for fixing clips and halters to light steel and timber purlins and rails
Features
Years / Environment
|
|||||||
---|---|---|---|---|---|---|---|
Interior | Semi-interior | Rural | Urban | Industrial / Coastal | Marine | Swimming pools & Chemical plants | |
Corrosivity Category | C1 | - | C2 | C3 | C4 | C5 | - |
Austenitic Stainless Steel A4 Grade (316) | 40 | 40 | 40 | 40 | 30 | 25 | 0 |
Substrate
Steel
|
1.2 mm |
Steel | |
0.5 mm | 1.61 kN |
NR,II,K (Tensile - Pull-out) | 0.5mm Steel: 0.91 kN |
1.2mm Steel: 2.97 kN | |
2mm Steel: 5.48 kN | |
18mm Plywood: 1.9 kN | |
Softwood C16: 2.19 kN |
Substrate
Steel
|
S19 washer |
Steel | 2 mm |
0.5 mm | 3.39 kN |
Installation tool | Variable speed electric screwdriver |
Installation drive | Fixfast GreenDrive (8mm hex integral socket with retaining clip) |
Installation speed | 1500 RPM |
Correct installation | Fasteners should be driven within three degrees of perpendicular to the surface of the fastened material. Use a depth-setting nosepiece to avoid over-driving, and do not over-tighten. Variants with bonded washers should not have the rubber compressed to less than two-thirds of its uncompressed height. Care should be taken when engaging and disengaging from the fastener head to avoid damage to the protective coating. |
Handling | Fasteners may have sharp edges, and the use of power tools can be dangerous. Use personal protective equipment. Store fasteners in dry conditions. Inspect each fastener before use and do not use damaged fasteners. |