Carbon steel lacquered clip fix fastener for fixing to light section steel.
Estimated lead times
2-3 Days
Estimated lead times
2-3 Days
Lacquered low profile fasteners for internal and external liner panel systems, trims and flashing details, framework and ductwork.
Features
- Variety of head styles, including ultra low profile
- All available in most RAL and BS colours
- For mechanically fixing metal sheeting systems to light metal purlins and rails
- For mechanically fixing components of steel and metal framing systems
Years / Environment
|
|||||||
---|---|---|---|---|---|---|---|
Interior | Semi-interior | Rural | Urban | Industrial / Coastal | Marine | Swimming pools & Chemical plants | |
Corrosivity Category | C1 | - | C2 | C3 | C4 | C5 | - |
Carbon steel case hardened | 25 | 20 | 12 | 0 | 0 | 0 | 0 |
Substrate
Steel
|
1.2 mm |
Steel | |
0.5 mm | 2.25 kN |
NR,II,K (Tensile - Pull-out) | 1.2mm Steel: 1.18 kN |
2mm Steel: 2.35 kN | |
3mm Steel: 4.09 kN |
Substrate
Steel
|
No washer |
Steel | 3 mm |
0.5 mm | 3.98 kN |
0.7 mm | 4.52 kN |
Installation tool | Variable speed electric screwdriver |
Installation drive | 2-PZD |
Installation speed | 1500 RPM |
Correct installation | Fasteners should be driven within three degrees of perpendicular to the surface of the fastened material. Use a depth-setting nosepiece to avoid over-driving, and do not over-tighten. Variants with bonded washers should not have the rubber compressed to less than two-thirds of its uncompressed height. Care should be taken when engaging and disengaging from the fastener head to avoid damage to the protective coating. |
Handling | Fasteners may have sharp edges, and the use of power tools can be dangerous. Use personal protective equipment. Store fasteners in dry conditions. Inspect each fastener before use and do not use damaged fasteners. |
Lacquered low profile fasteners for internal and external liner panel systems, trims and flashing details, framework and ductwork.
Features
- Variety of head styles, including ultra low profile
- All available in most RAL and BS colours
- For mechanically fixing metal sheeting systems to light metal purlins and rails
- For mechanically fixing components of steel and metal framing systems
Years / Environment
|
|||||||
---|---|---|---|---|---|---|---|
Interior | Semi-interior | Rural | Urban | Industrial / Coastal | Marine | Swimming pools & Chemical plants | |
Corrosivity Category | C1 | - | C2 | C3 | C4 | C5 | - |
Carbon steel case hardened | 25 | 20 | 12 | 0 | 0 | 0 | 0 |
Substrate
Steel
|
1.2 mm |
Steel | |
0.5 mm | 2.25 kN |
NR,II,K (Tensile - Pull-out) | 1.2mm Steel: 1.18 kN |
2mm Steel: 2.35 kN | |
3mm Steel: 4.09 kN |
Substrate
Steel
|
No washer |
Steel | 3 mm |
0.5 mm | 3.98 kN |
0.7 mm | 4.52 kN |
Installation tool | Variable speed electric screwdriver |
Installation drive | 2-PZD |
Installation speed | 1500 RPM |
Correct installation | Fasteners should be driven within three degrees of perpendicular to the surface of the fastened material. Use a depth-setting nosepiece to avoid over-driving, and do not over-tighten. Variants with bonded washers should not have the rubber compressed to less than two-thirds of its uncompressed height. Care should be taken when engaging and disengaging from the fastener head to avoid damage to the protective coating. |
Handling | Fasteners may have sharp edges, and the use of power tools can be dangerous. Use personal protective equipment. Store fasteners in dry conditions. Inspect each fastener before use and do not use damaged fasteners. |