A4/316 grade stainless steel stitching fasteners, supplied pre-assembled with a stainless steel / EPDM rubber 15mm diameter sealing washer, normally used in wall applications.
Estimated lead times
1 Day
Estimated lead times
1 Day
Stainless steel stitching fastener for stitching together two steel sheets up to 1mm thick.
Features
- A4 grade stainless steel
- Free spin zone prevents fasteners from being over driven
- Supplied pre-assembled with an A4 Stainless steel/ EPDM rubber 15mm diameter sealing washer, normally used in vertical applications
- For mechanically fixing (stitching) two metal sheets up to 1mm thick together
Years / Environment
|
|||||||
---|---|---|---|---|---|---|---|
Interior | Semi-interior | Rural | Urban | Industrial / Coastal | Marine | Swimming pools & Chemical plants | |
Corrosivity Category | C1 | - | C2 | C3 | C4 | C5 | - |
Austenitic Stainless Steel A4 Grade (316) | 40 | 40 | 40 | 40 | 30 | 25 | 0 |
Substrate
Steel
|
0.5 mm |
Steel | |
0.5 mm | 1.05 kN |
NR,II,K (Tensile - Pull-out) | 0.5mm Steel: 0.6 kN |
Substrate
Steel
|
S15 washer |
Steel | 0.5 mm |
0.5 mm | 3.6 kN |
Installation tool | Variable speed electric screw gun |
Installation drive | Fixfast GreenDrive (8mm hex integral socket with retaining clip) |
Installation speed | 1500 RPM |
Correct installation | Fasteners should be driven within three degrees of perpendicular to the surface of the fastened material. Use a depth-setting nosepiece to avoid over-driving, and do not over-tighten. Variants with bonded washers should not have the rubber compressed to less than two-thirds of its uncompressed height. Care should be taken when engaging and disengaging from the fastener head to avoid damage to the protective coating. |
Handling | Fasteners may have sharp edges, and the use of power tools can be dangerous. Use personal protective equipment. Store fasteners in dry conditions. Inspect each fastener before use and do not use damaged fasteners. |
Stainless steel stitching fastener for stitching together two steel sheets up to 1mm thick.
Features
- A4 grade stainless steel
- Free spin zone prevents fasteners from being over driven
- Supplied pre-assembled with an A4 Stainless steel/ EPDM rubber 15mm diameter sealing washer, normally used in vertical applications
- For mechanically fixing (stitching) two metal sheets up to 1mm thick together
Years / Environment
|
|||||||
---|---|---|---|---|---|---|---|
Interior | Semi-interior | Rural | Urban | Industrial / Coastal | Marine | Swimming pools & Chemical plants | |
Corrosivity Category | C1 | - | C2 | C3 | C4 | C5 | - |
Austenitic Stainless Steel A4 Grade (316) | 40 | 40 | 40 | 40 | 30 | 25 | 0 |
Substrate
Steel
|
0.5 mm |
Steel | |
0.5 mm | 1.05 kN |
NR,II,K (Tensile - Pull-out) | 0.5mm Steel: 0.6 kN |
Substrate
Steel
|
S15 washer |
Steel | 0.5 mm |
0.5 mm | 3.6 kN |
Installation tool | Variable speed electric screw gun |
Installation drive | Fixfast GreenDrive (8mm hex integral socket with retaining clip) |
Installation speed | 1500 RPM |
Correct installation | Fasteners should be driven within three degrees of perpendicular to the surface of the fastened material. Use a depth-setting nosepiece to avoid over-driving, and do not over-tighten. Variants with bonded washers should not have the rubber compressed to less than two-thirds of its uncompressed height. Care should be taken when engaging and disengaging from the fastener head to avoid damage to the protective coating. |
Handling | Fasteners may have sharp edges, and the use of power tools can be dangerous. Use personal protective equipment. Store fasteners in dry conditions. Inspect each fastener before use and do not use damaged fasteners. |