A4/316 grade stainless steel low profile stitching fastener, supplied pre-assembled with a stainless steel / EPDM rubber 15mm diameter sealing washer, normally used in wall applications
Max stitching capacity: 2 x 1mm sheet steel.
Estimated lead times
1 Day
Estimated lead times
1 Day
Stainless steel low profile stitching fastener for stitching together two steel sheets up to 1mm thick.
Features
- A4/316 grade stainless steel
- Free spin zone prevents thread strip out
- Supplied pre-assembled with an Aluminium / EPDM rubber 15mm diameter sealing washer, normally used in wall applications
- For mechanically fixing (stitching) two metal sheets up to 1mm thick together
Years / Environment
|
|||||||
---|---|---|---|---|---|---|---|
Interior | Semi-interior | Rural | Urban | Industrial / Coastal | Marine | Swimming pools & Chemical plants | |
Corrosivity Category | C1 | - | C2 | C3 | C4 | C5 | - |
Austenitic Stainless Steel A4 Grade (316) | 40 | 40 | 40 | 40 | 30 | 25 | 0 |
Substrate
Steel
|
0.5 mm |
Steel | |
0.5 mm | 1.02 kN |
NR,II,K (Tensile - Pull-out) | 0.5mm Steel: 0.56 kN |
Substrate
Steel
|
S15 washer |
Steel | 0.5 mm |
0.5 mm | 4.01 kN |
Installation tool | Variable speed electric screwdriver |
Installation drive | Fixfast RedDrive |
Installation speed | 1500 RPM |
Correct installation | Fasteners should be driven within three degrees of perpendicular to the surface of the fastened material. Use a depth-setting nosepiece to avoid over-driving, and do not over-tighten. Variants with bonded washers should not have the rubber compressed to less than two-thirds of its uncompressed height. Care should be taken when engaging and disengaging from the fastener head to avoid damage to the protective coating. |
Handling | Fasteners may have sharp edges, and the use of power tools can be dangerous. Use personal protective equipment. Store fasteners in dry conditions. Inspect each fastener before use and do not use damaged fasteners. |
Stainless steel low profile stitching fastener for stitching together two steel sheets up to 1mm thick.
Features
- A4/316 grade stainless steel
- Free spin zone prevents thread strip out
- Supplied pre-assembled with an Aluminium / EPDM rubber 15mm diameter sealing washer, normally used in wall applications
- For mechanically fixing (stitching) two metal sheets up to 1mm thick together
Years / Environment
|
|||||||
---|---|---|---|---|---|---|---|
Interior | Semi-interior | Rural | Urban | Industrial / Coastal | Marine | Swimming pools & Chemical plants | |
Corrosivity Category | C1 | - | C2 | C3 | C4 | C5 | - |
Austenitic Stainless Steel A4 Grade (316) | 40 | 40 | 40 | 40 | 30 | 25 | 0 |
Substrate
Steel
|
0.5 mm |
Steel | |
0.5 mm | 1.02 kN |
NR,II,K (Tensile - Pull-out) | 0.5mm Steel: 0.56 kN |
Substrate
Steel
|
S15 washer |
Steel | 0.5 mm |
0.5 mm | 4.01 kN |
Installation tool | Variable speed electric screwdriver |
Installation drive | Fixfast RedDrive |
Installation speed | 1500 RPM |
Correct installation | Fasteners should be driven within three degrees of perpendicular to the surface of the fastened material. Use a depth-setting nosepiece to avoid over-driving, and do not over-tighten. Variants with bonded washers should not have the rubber compressed to less than two-thirds of its uncompressed height. Care should be taken when engaging and disengaging from the fastener head to avoid damage to the protective coating. |
Handling | Fasteners may have sharp edges, and the use of power tools can be dangerous. Use personal protective equipment. Store fasteners in dry conditions. Inspect each fastener before use and do not use damaged fasteners. |